Milk Standardisation Plant

Concept Design: Milk Standardisation Plant with Two SS Tanks

1. Design Basis

This concept uses two hygienic stainless-steel tanks for batch milk standardisation. Final capacities, throughput, fat targets, and utility loads shall be confirmed during detailed design.

  • Product: chilled raw or pasteurised milk
  • Operation: batch receipt, blending, verification, and transfer
  • Product-contact material: SS 316L; external non-contact parts may be SS 304
  • Indicative tank construction: insulated, closed, vertical tanks with sloped bottoms
  • Indicative design temperature: product service suitable for chilled milk and hot CIP circulation

2. Process Flow

Milk reception or upstream balance → Tank 1: receiving and blend preparation → controlled addition of cream or skim milk → agitation and sample verification → Tank 2: standardised milk holding → downstream pasteuriser, filler, or storage.

A sanitary transfer pump moves product between the tanks. A hygienic valve manifold separates product, drain, and CIP routes and prevents unintended mixing.

3. Tank Duties

Tank 1 — Milk Receiving and Standardisation Tank

  • Receives the base milk and measured cream or skim milk.
  • Fitted with a slow-speed hygienic agitator for uniform blending without excessive foaming.
  • Includes load cells or a level transmitter, temperature indication, high-level protection, a sampling valve, spray device, vent filter, manway, and insulated jacket.

Tank 2 — Standardised Milk Holding Tank

  • Receives the verified standardised milk batch.
  • Provides gentle agitation and chilled holding before downstream processing.
  • Includes level and temperature instruments, high- and low-level protection, a sampling valve, spray device, vent filter, manway, and insulated jacket.

4. Equipment Schedule

ItemQty.Indicative specification
SS Tank 11SS 316L product contact, insulated, jacketed, hygienic agitator, CIP spray device
SS Tank 21SS 316L product contact, insulated, jacketed, hygienic agitator, CIP spray device
Sanitary transfer pump1 dutyVariable-speed centrifugal pump sized for required transfer rate and pressure drop
Dosing arrangement1 setMetered cream and/or skim-milk addition with hygienic valves and flow measurement
Valve manifold and pipework1 setDrainable hygienic pipework with separated product and CIP routes
Control panel1PLC/HMI with batch sequence, permissives, alarms, trends, and recipe control

5. Controls and Interlocks

  • Recipe entry for target batch quantity and fat percentage.
  • Automatic calculation and metering of cream or skim-milk addition based on verified incoming composition.
  • Agitator operation permitted only above the minimum safe product level.
  • Transfer prevented on high level in the receiving tank or incorrect valve alignment.
  • Low-level pump protection and high-high-level shutdown.
  • Batch record for quantities, temperatures, operator actions, analytical result, and release status.

6. Hygienic and Utility Requirements

  • Fully drainable product-contact surfaces, orbital-welded hygienic pipework, and minimal dead legs.
  • Food-grade seals compatible with milk, cleaning chemicals, and operating temperatures.
  • CIP coverage for both tanks, transfer line, dosing line, pump, and valve manifold; return conductivity and temperature monitoring are recommended.
  • Utilities: chilled water or glycol, hot water/CIP supply, potable water, compressed air, electrical power, and drainage.
  • Provide safe access to manways and instruments, bunding or controlled drainage where required, and suitable floor falls.

7. Inputs Required for Detailed Design

  • Required plant throughput and batch size
  • Working and gross capacity of each tank
  • Incoming and target fat percentages
  • Product inlet and outlet temperatures
  • Required holding time and downstream process
  • Applicable local food-safety, pressure-equipment, electrical, and building requirements
  • Available CIP parameters and utility capacities

Note: This is a conceptual process brief. A qualified dairy process engineer shall complete the mass balance, hygienic risk review, mechanical design, instrumentation schedule, utility sizing, and regulatory compliance checks before fabrication or installation.

Download Complete Dairy Solution Brochure PDF

Contact

Company No. 17285207
[email protected]